Restart and Reset of the SALUS SQ610RF Quantum Thermostat

Restart and Reset of the SALUS SQ610RF Quantum Thermostat

The SALUS SQ610RF Quantum is a modern wireless temperature controller based on ZigBee technology, compatible with the SALUS iT600 system. If you need to restart or restore factory settings, there are several reset options available – both directly from the device and via the mobile app.



1. Soft Restart (Manual Reboot)

Purpose: Quickly reboot the device without deleting settings or unpairing.

How to perform:

  1. Press and hold the OK button for 6 seconds.

  2. The thermostat will shut down (enter Sleep Mode).

  3. To power it back on – press and hold OK for 6 seconds again.

Effect: The thermostat restarts with all configurations and device pairings retained.



2. User Settings Reset ( Soft Reset )

Purpose: Resets user settings like schedules, names, and temperature presets – without removing the device from the ZigBee network.

How to perform:

  1. Open the SALUS SmartHome app and go to your device settings.

  2. Navigate to “User Settings”.

  3. Select “Reset User Settings” and confirm.

Effect: Restores default temperatures, schedules, and names. Device remains paired with the ZigBee network.


3. ZigBee Unpairing (Network Reset Only)

Purpose: Unlinks the thermostat from the current ZigBee gateway or coordinator but retains local settings.

How to perform:

  1. In the app, open the SQ610RF Quantum interface.

  2. Scroll down and tap “Remove SQ610RF Quantum”.

  3. Confirm the action.

Effect: The thermostat is removed from the ZigBee network and disappears from the app. Its local settings are preserved.



4. Full Factory Reset (Hard Reset)

Purpose: Completely restores factory settings – deletes all user data, pairings, schedules, PINs, etc.

Two methods:

a) From the mobile app:

  1. Go to Device Settings in the app.

  2. Scroll down and select “Factory Reset”.

  3. Confirm with “YES”.

b) From the device menu:

  1. Enter the Installer Menu (Menu → press and hold for 3 seconds).

  2. Select “Factory Reset” from the list.

  3. Confirm the action.

Effect: The thermostat will be fully reset. It must be re-paired and configured from scratch.

​

Additional Notes;

  • After a factory reset, if the device still appears in the app, remove it manually (the tile will turn grey).

  • PIN codes and button lockouts are also cleared during a factory reset.

  • During ZigBee pairing, pressing and holding the OK button for 3 seconds resets the pairing process only.

    • Related Articles

    • Firmware Update for SQ610 and SQ610RF Thermostat

      To ensure proper operation and access to the latest features, it is recommended to regularly check for firmware updates for your SALUS devices. How to check and update the firmware: Log in to your SALUS Premium lite account using the mobile app or a ...

    • Frozen Display – What to Do When the Thermostat Doesn’t Respond

      If the screen is frozen and the device is not responding to touch or button presses, try one of the reset options below. Both methods restart the device without erasing your settings or paired devices. 1. Soft Reset Purpose: to quickly restart the ...

    • How to exit Standby mode in the app and on the thermostat

      If Standby mode is enabled and you want to deactivate it, there are two ways to do it: 1. On the thermostat: Press and hold the power (“OK”) button for about 5 seconds. This toggles Standby mode on or off (works both ways). 2. In the SALUS Premium ...

    • Activating Cooling Mode

      The ability to activate cooling depends on how your system is configured and which devices are connected. Thermostat works independently (not connected to KL08RF) Using the Salus Premium Lite app Log into the Salus Premium Lite app. Tap the tile for ...

    • Incorrect Temperature Displayed (Too High or Too Low)

      If the thermostat seems to show a temperature that doesn’t match the actual room temperature, you can adjust the displayed value using the temperature offset function. The adjustment range is from -3.5°C to +3.5°C. How to adjust the displayed ...